- 1) Introduction
- 2) Notational Conventions and Generic Grammar
- 3) Protocol Parameters
- 4) HTTP Message
- 5) Request
- 6) Response
- 7) Entity
- 8) Connections
- 9) Method Definitions
- 10) Status Code Definitions
- 1) Informational 1xx
- 2) Successful 2xx
- 3) Redirection 3xx
- 4) Client Error 4xx
- 1) 400 Bad Request
- 2) 401 Unauthorized
- 3) 402 Payment Required
- 4) 403 Forbidden
- 5) 404 Not Found
- 6) 405 Method Not Allowed
- 7) 406 Not Acceptable
- 8) 407 Proxy Authentication Required
- 9) 408 Request Timeout
- 10) 409 Conflict
- 11) 410 Gone
- 12) 411 Length Required
- 13) 412 Precondition Failed
- 14) 413 Request Entity Too Large
- 15) 414 Request-URI Too Long
- 16) 415 Unsupported Media Type
- 17) 416 Requested Range Not Satisfiable
- 18) 417 Expectation Failed
- 5) Server Error 5xx
- 11) Access Authentication
- 12) Content Negotiation
- 13) Caching in HTTP
- 1) ..
- 2) Expiration Model
- 3) Validation Model
- 4) Response Cacheability
- 5) Constructing Responses From Caches
- 6) Caching Negotiated Responses
- 7) Shared and Non-Shared Caches
- 8) Errors or Incomplete Response Cache Behavior
- 9) Side Effects of GET and HEAD
- 10) Invalidation After Updates or Deletions
- 11) Write-Through Mandatory
- 12) Cache Replacement
- 13) History Lists
- 14) Header Field Definitions
- 1) Accept
- 2) Accept-Charset
- 3) Accept-Encoding
- 4) Accept-Language
- 5) Accept-Ranges
- 6) Age
- 7) Allow
- 8) Authorization
- 9) Cache-Control
- 10) Connection
- 11) Content-Encoding
- 12) Content-Language
- 13) Content-Length
- 14) Content-Location
- 15) Content-MD5
- 16) Content-Range
- 17) Content-Type
- 18) Date
- 19) ETag
- 20) Expect
- 21) Expires
- 22) From
- 23) Host
- 24) If-Match
- 25) If-Modified-Since
- 26) If-None-Match
- 27) If-Range
- 28) If-Unmodified-Since
- 29) Last-Modified
- 30) Location
- 31) Max-Forwards
- 32) Pragma
- 33) Proxy-Authenticate
- 34) Proxy-Authorization
- 35) Range
- 36) Referer
- 37) Retry-After
- 38) Server
- 39) TE
- 40) Trailer
- 41) Transfer-Encoding
- 42) Upgrade
- 43) User-Agent
- 44) Vary
- 45) Via
- 46) Warning
- 47) WWW-Authenticate
- 15) Security Considerations
- 16) Acknowledgments
- 17) References
- 18) Authors' Addresses
- 19) Appendices
- 20) Index
- 21) Full Copyright Statement
- 22) Acknowledgement
8.1.2 Overall Operation
A significant difference between HTTP/1.1 and earlier versions of HTTP is that persistent connections are the default behavior of any HTTP connection. That is, unless otherwise indicated, the client SHOULD assume that the server will maintain a persistent connection, even after error responses from the server.
Persistent connections provide a mechanism by which a client and a server can signal the close of a TCP connection. This signaling takes place using the Connection header field (Section 14.10). Once a close has been signaled, the client MUST NOT send any more requests on that connection.
8.1.2.1 Negotiation
An HTTP/1.1 server MAY assume that a HTTP/1.1 client intends to maintain a persistent connection unless a Connection header including the connection-token "close" was sent in the request. If the server chooses to close the connection immediately after sending the response, it SHOULD send a Connection header including the connection-token close.
An HTTP/1.1 client MAY expect a connection to remain open, but would decide to keep it open based on whether the response from a server contains a Connection header with the connection-token close. In case the client does not want to maintain a connection for more than that request, it SHOULD send a Connection header including the connection-token close.
If either the client or the server sends the close token in the Connection header, that request becomes the last one for the connection.
Clients and servers SHOULD NOT assume that a persistent connection is maintained for HTTP versions less than 1.1 unless it is explicitly signaled. See Section 19.6.2 for more information on backward compatibility with HTTP/1.0 clients.
In order to remain persistent, all messages on the connection MUST have a self-defined message length (i.e., one not defined by closure of the connection), as described in Section 4.4.
8.1.2.2 Pipelining
A client that supports persistent connections MAY "pipeline" its requests (i.e., send multiple requests without waiting for each response). A server MUST send its responses to those requests in the same order that the requests were received.
Clients which assume persistent connections and pipeline immediately after connection establishment SHOULD be prepared to retry their connection if the first pipelined attempt fails. If a client does such a retry, it MUST NOT pipeline before it knows the connection is persistent. Clients MUST also be prepared to resend their requests if the server closes the connection before sending all of the corresponding responses.
Clients SHOULD NOT pipeline requests using non-idempotent methods or non-idempotent sequences of methods (see Section 9.1.2). Otherwise, a premature termination of the transport connection could lead to indeterminate results. A client wishing to send a non-idempotent request SHOULD wait to send that request until it has received the response status for the previous request.